Free shipping to the lower 48 states on every order

Not sure what fits? Take the 60-second fireplace finder

Electric fireplaces need no chimney or vent. Here is why

How to Install an Electric Fireplace Insert: Steps and Safety

A plug-in electric insert is an afternoon job if the outlet is in the right place. Here's the tool list, the safety steps that matter, nine install steps and the mistakes we see most.

Electric fireplace insert installed in a whitewashed brick fireplace with a level on the hearth
In this guide 10 sections
  1. Before you start: confirm the fit
  2. Tools and materials
  3. Safety first: power, drafts and the chimney
  4. How to install an electric fireplace insert, step by step
  5. Routing and hiding the cord
  6. Plug-in or hardwired?
  7. Installing an insert in a TV stand or cabinet
  8. Common installation mistakes
  9. What it costs to run once it's in
  10. FAQ

The insert itself is the easy part. Power and drafts are where installs go wrong, so most of this guide is about those two things.

Before you start: confirm the fit

If you haven’t measured yet, stop here and do that first. You need the front width and height, the rear width and the depth at the floor and higher up, because most fireboxes taper. Our guide on how to measure for an electric fireplace insert walks through it with a size chart.

This guide covers plug-in inserts going into a masonry fireplace, a factory-built (prefab) firebox, or the firebox cavity of a TV stand or cabinet.

Tools and materials

  • Tape measure and a level
  • Phillips screwdriver
  • Flashlight and work gloves
  • Shop vacuum for ash and soot
  • Composite or wood shims
  • A plug-in outlet tester (a few dollars at any hardware store)
  • Chimney balloon or rigid flue cover, if your damper doesn’t seal
  • Paintable cord cover, if the outlet is outside the firebox
  • A helper. Inserts are awkward to carry, and the larger ones are listed at over 30 pounds.

Safety first: power, drafts and the chimney

Turn off power to any outlet you’re working on. If you’re only plugging into an existing outlet, you can leave the breaker on. If anyone is opening a box or adding a receptacle, the breaker goes off first and that work belongs to an electrician.

Never use an extension cord or power strip. Plug the insert straight into a wall outlet. A heater pulls steady current for hours, and light-duty cords and strips can overheat. The Electrical Safety Foundation’s space heater safety tips say the same thing, and an electric fireplace heater is a space heater as far as your wiring is concerned.

Check the circuit. A 1,500 W heater draws about 12.5 amps at 120 volts, and a 1,400 W heater about 11.7 amps. On a typical 15-amp circuit that leaves little room for anything else. If the same circuit runs a vacuum, a space heater or a window AC, expect tripped breakers. A dedicated circuit is the safe bet.

Close the damper and stop drafts. The insert doesn’t vent, so the chimney has no job anymore. An open flue lets cold air, rain and debris fall in and lets warm room air escape.

Know what else uses the chimney. Some chimneys carry a separate flue for a furnace or water heater. Only block the fireplace flue. Never cover a flue that vents another appliance.

How to install an electric fireplace insert, step by step

  1. Clean the firebox. Remove the grate, andirons and loose debris, then vacuum the ash. Soot smears onto the insert’s finish and gets blown around by the heater fan.
  2. Close the damper and block drafts. Shut the damper. If it’s warped or rusted open, fit a chimney balloon or a rigid flue cover. Hang a tag on the damper handle that says the flue is blocked and the fireplace is not for burning, so a future owner or house guest doesn’t light a fire.
  3. Get power where you need it. The cleanest setup is an outlet inside the firebox or right next to the opening. If there isn’t one, have an electrician add it before install day. Test the outlet with your plug-in tester to confirm it’s wired and grounded correctly.
  4. Unbox and inspect. Remove the packing, any shipping brackets and protective film. Check the glass and the trim for damage before you go any further.
  5. Do a test run outside the fireplace. Set the insert on the floor, plug it in and run the flame, then the heater, for a few minutes. Try the remote and the timer. Finding a problem now saves you pulling the unit back out of the firebox later.
  6. Attach the trim or surround. If your insert came with a trim kit, or you bought one, fit it now while you can reach the screws. A three-sided frame is easier when the insert sits on the firebox floor.
  7. Set the insert in and plug it in. Slide it most of the way in, reach behind and plug it in, then push it home. Leave a little slack in the cord so it isn’t pulled tight or pinched under the unit.
  8. Level and center it. Old brick floors are rarely flat. Shim under the feet until the insert is level side to side and the trim sits flush against the face. Check that nothing blocks the heat vent or the air intake.
  9. Switch on and test again. Run flame-only first, then heat on low, then high. A faint smell the first time the heater runs is common with new heating elements and should fade. Set your clock, timer and thermostat.

Routing and hiding the cord

With the outlet inside the firebox, the cord stays out of sight and you’re done. With the outlet outside, run the cord out through a bottom corner of the trim, then along the hearth or baseboard to the outlet. A paintable cord cover keeps it neat and keeps people from tripping on it.

Don’t run the cord under a rug, don’t staple it, and don’t let it pass in front of the heat vent. If the cord can’t reach the outlet without an extension, the answer is a new outlet, not a longer cord.

Plug-in or hardwired?

Most inserts, including ours, are sold as plug-in 120V units. Some brands offer a hardwire option. If you want one, check the manual first, because not every insert allows it.

Plug-in Hardwired
Who installs it You A licensed electrician
Permit Not usually Often required, depending on local code
Look Clean if the outlet is inside the firebox, visible cord if not No cord at all
Cost Nothing beyond the insert, unless you need a new outlet Electrician’s labor and materials
Moving it later Unplug and go Needs the electrician again

Installing an insert in a TV stand or cabinet

The same rules apply, just with less masonry. The cavity in a fireplace TV stand is cut for a set size, so check that the insert matches it. Slide it in, feed the cord out through the hole in the back panel, and keep the front vent unobstructed. A unit like our 23-inch insert is listed for use recessed in a wall or in furniture, and the maker pitches it as a replacement for older TV stand fireboxes. Browse our other electric fireplace inserts if you need a different size.

Common installation mistakes

Mistake What happens Fix
Extension cord or power strip Overheated cord, fire risk Plug straight into a wall outlet, or add one
Damper left open Drafts, a cold room, warm air lost up the flue Close it, or block the flue
Measuring only the front Insert hits the tapered back wall Measure rear width and depth up high
Heater sharing a busy circuit Tripped breaker every evening Move other loads or add a dedicated circuit
Trim or decor covering the vent Overheat protection shuts the heater off Keep vents clear
Cord pinched under or behind the unit Damaged insulation Leave slack, reroute
Skipping the test run Pulling the insert back out to fix a fault Run it on the floor first

If the insert won’t power on or the heat cuts out after install, our electric fireplace troubleshooting guide covers the usual causes.

What it costs to run once it’s in

At about 17¢ per kWh, a 1,400 W insert costs about 24¢ an hour on high heat and a 1,500 W insert about 26¢. Flame-only mode costs much less. Our guide on how much electricity an electric fireplace uses has the full math.

FAQ

Who can install an electric fireplace insert?

You can, if you’re plugging into an existing outlet. It’s lifting, sliding and leveling. Call a licensed electrician for a new outlet, a new circuit or a hardwired setup, and a licensed gas professional if there’s a gas line in the firebox that needs to be capped.

How do you plug in an electric fireplace insert?

Straight into a grounded wall outlet, ideally one inside or right beside the firebox. Plug it in before you push the insert all the way in, and leave a little slack. Never use an extension cord or power strip.

How do I hide the cord for an electric fireplace insert?

The best way is an outlet inside the firebox, so the cord never shows. If the outlet is outside, route the cord through a bottom corner of the trim and cover the run with a paintable cord cover. Don’t run it under rugs.

How much does it cost to install an electric fireplace insert?

If you already have a good outlet in reach, the install itself costs nothing but your time. The main extra cost is an electrician if you need a new outlet, a new circuit or a hardwired connection. Get a quote, since prices vary by area and by how hard it is to reach the firebox.

Is it easy to install an electric fireplace insert in an existing fireplace?

Yes, for most people. The hard parts are measuring correctly, sealing the damper and having power in the right spot. Get those three right and the insert slides in. Questions about a specific insert before you order? Contact us and we’ll walk you through it.

Written by The Fireplace Co. team

We write our guides from manufacturer specs and published safety standards, and update them when specs change. Spotted something out of date, or need help with your room? Ask us.

Free shipping

To the lower 48 states, on every order

No vent or gas line

Most models plug into a standard outlet

Not sure which one fits?
Find your fireplace in about a minute
Four quick questions about your room and TV, and you get a shortlist that fits.
Try the Fireplace Finder
The Fireplace Co.
Welcome offer
Take 10% off your first order
Sizing tips, new arrivals and early sale access. Your code appears as soon as you sign up.
Get my 10% code
One code per customer. No spam, unsubscribe any time.
No thanks
Welcome offer
Take 10% off your first order
Sizing tips, new arrivals and early sale access.
Get my 10% code
One code per customer. No spam, unsubscribe any time.
No thanks