How Much Electricity Does an Electric Fireplace Use? Real Costs
An electric fireplace uses 1,400 to 1,500 W on high heat, roughly 24 to 26 cents an hour at 17¢ per kWh, and the LED flame alone costs under a penny an hour. Here are the cost tables at four electricity rates, the amp math and the habits that keep the bill down.
In this guide 8 sections
- The one formula you need: watts to kWh to dollars
- Cost per hour at 12¢, 17¢, 25¢ and 35¢ per kWh
- Daily and monthly cost if you run it 4 hours a night
- Do electric fireplaces use a lot of electricity?
- Amps, outlets and breakers
- How to lower the cost without giving up the fire
- Choosing a fireplace with running costs in mind
- FAQ
So no, an electric fireplace doesn’t use a shocking amount of power, but the heater is one of the bigger loads you can plug into a wall outlet. The flame is cheap. The heat is where the money goes. Below is the math at four different electricity rates, what the fireplace asks of your outlet and breaker, and the habits that keep the monthly number small.
The one formula you need: watts to kWh to dollars
Your utility bills you in kilowatt-hours. One kWh is 1,000 watts running for one hour. That gives you a simple formula:
Cost per hour = watts ÷ 1,000 × your rate per kWh
For a 1,500 W heater at 17¢: 1,500 ÷ 1,000 × $0.17 = $0.255, so about 26 cents an hour. For 1,400 W: 1.4 × $0.17 = $0.238, about 24 cents.
Most electric fireplaces have two heat settings. The common pairs are 750 W and 1,500 W, or 700 W and 1,400 W. Our compact electric fireplace stove, for example, switches between 750 W and 1,500 W. You’ll find your unit’s numbers on the rating label (usually on the back or underneath) and in the spec table of the manual.
One thing that trips people up: product listings often round heat output. Plenty of 1,400 W fireplaces are advertised as “5,000 BTU.” The actual conversion is 1 watt = 3.412 BTU per hour, so 1,400 W works out to about 4,777 BTU and 1,500 W to about 5,118 BTU. When the watts and the BTU disagree, trust the watts. They’re what your meter counts.
Cost per hour at 12¢, 17¢, 25¢ and 35¢ per kWh
The U.S. Energy Information Administration’s Electric Power Monthly (Table 5.6.A) put the average U.S. residential price at 18.16¢ per kWh for August 2026. That average hides a wide spread. Rates change by season, by state and by utility, and some households pay closer to 12¢ while others pay well over 30¢. We run our product math at about 17¢ per kWh, and the table shows what happens above and below that.
| Setting | Energy per hour | At 12¢/kWh | At 17¢/kWh | At 25¢/kWh | At 35¢/kWh |
|---|---|---|---|---|---|
| High heat, 1,500 W | 1.5 kWh | 18¢ | 26¢ | 38¢ | 53¢ |
| High heat, 1,400 W | 1.4 kWh | 17¢ | 24¢ | 35¢ | 49¢ |
| Low heat, 750 W | 0.75 kWh | 9¢ | 13¢ | 19¢ | 26¢ |
| Flame only, roughly 15 to 50 W | 0.015 to 0.05 kWh | 0.2 to 0.6¢ | 0.3 to 0.9¢ | 0.4 to 1.3¢ | 0.5 to 1.8¢ |
About that flame-only row: LED flame effects usually draw roughly 15 to 50 W depending on the model, the brightness setting and whether extras like colored ember beds or backlights are on. Your manual or rating label will list the exact figure. Even at the high end, you’d need to run the flame for more than an hour to spend two cents.
Daily and monthly cost if you run it 4 hours a night
Hourly numbers are hard to feel. Here is the same math stretched over a month, assuming 4 hours a day for 30 days (120 hours):
| Setting | kWh per day | Per day at 17¢ | Month at 12¢ | Month at 17¢ | Month at 25¢ | Month at 35¢ |
|---|---|---|---|---|---|---|
| 1,500 W | 6 | $1.02 | $21.60 | $30.60 | $45.00 | $63.00 |
| 1,400 W | 5.6 | $0.95 | $20.16 | $28.56 | $42.00 | $58.80 |
| 750 W | 3 | $0.51 | $10.80 | $15.30 | $22.50 | $31.50 |
| Flame only, 15 to 50 W | 0.06 to 0.2 | 1 to 3¢ | $0.22 to $0.72 | $0.31 to $1.02 | $0.45 to $1.50 | $0.63 to $2.10 |
Run it 8 hours a day and you double every number. Run it 2 hours and you halve them.
Treat the heater rows as a ceiling, not a forecast. Most of the fireplaces we sell have a built-in thermostat, often adjustable from 64 to 82°F. Once the room reaches the set temperature, the heating element cycles off and the fan slows or stops, then it kicks back on as the room cools. If the heater ends up running half of those 4 hours, a 1,500 W unit costs closer to $15 a month at 17¢ than $30. A drafty room on a cold night will run it more. A mild evening, less.
Do electric fireplaces use a lot of electricity?
For a single plug-in appliance, yes, the heater is near the top of the list. A 120 V plug-in heater is effectively capped around 1,500 W, which is about the same draw as a hair dryer on high or a toaster. The difference is time. You run a hair dryer for ten minutes. You might run a fireplace heater for four hours.
Compared with heating a whole house, it’s a different story. Your furnace or heat pump warms every room, including the ones nobody is sitting in. An electric fireplace warms one room. That’s the idea behind zone heating: let the central thermostat sit a few degrees lower and add heat only where people actually are.
Be realistic about where the savings come from. Electric resistance heat turns essentially every watt into heat, but a modern heat pump can move more heat than the electricity it uses, so for each unit of heat delivered, a heat pump is usually cheaper. The fireplace saves money only when it lets you heat less space, not because its heat is cheaper. If you run the fireplace and leave the central thermostat where it was, your bill goes up. If you turn the central heat down and use the fireplace in the family room, it can go down.
Amps, outlets and breakers
Amps are watts divided by volts. On a standard 120 V household outlet:
- 1,500 W ÷ 120 V = 12.5 amps
- 1,400 W ÷ 120 V = about 11.7 amps
- 750 W ÷ 120 V = 6.25 amps
- Flame only, 50 W ÷ 120 V = under half an amp
Most living room and bedroom circuits are 15 amps, some are 20. Electricians generally keep a load that runs for hours at no more than 80 percent of the breaker rating, which is 12 amps on a 15-amp circuit and 16 amps on a 20-amp circuit. A 1,500 W heater on high is already past that 12-amp line by itself. Add a TV, a sound bar and a couple of lamps on the same circuit and a tripped breaker is likely.
That’s why many manufacturers recommend a dedicated circuit, or at least a circuit with nothing else heavy on it. Check your manual for the exact requirement. And plug the fireplace straight into a wall outlet. The Consumer Product Safety Commission’s winter heating guidance is blunt about it: plug electric space heaters directly into a wall outlet, never into an extension cord or power strip. If the plug or the outlet cover ever feels warm, stop using that outlet and have it checked.
How to lower the cost without giving up the fire
A few habits make a bigger difference than any feature on the spec sheet.
- Warm up on high, then drop to low. Going from 1,500 W to 750 W cuts the hourly cost in half, from about 26¢ to about 13¢ at 17¢ per kWh.
- Set the thermostat, don’t max it. 68 to 70°F feels comfortable in most living rooms. Cranking it to 82°F just keeps the element running.
- Use the timer. Some units, such as our 33-inch insert with a 1 to 9 hour timer, shut the heater off on schedule, so you don’t pay for the hours after you’ve left the room.
- Close the door. A 1,500 W heater can make a closed 200 sq ft den noticeably warmer. In an open floor plan, much of that heat drifts into the kitchen and up the stairs.
- Turn the central heat down a few degrees while you’re using the fireplace in one room. This is where zone heating actually saves money.
- Run flame only in spring and fall. You get the look for pennies a month.
If you’re thinking about running it overnight, read our guide on whether you can leave an electric fireplace on all night first. The safety advice and the cost advice point in the same direction.
Choosing a fireplace with running costs in mind
Bigger fireplaces don’t use more electricity for heat. A 60-inch wall unit and a 23-inch insert usually both top out at 1,400 to 1,500 W, because that’s what a standard 120 V outlet can safely supply. What changes is the flame display and, on some models, the brightness of the LEDs. So pick the size that fits your wall or TV, and expect roughly the same heating cost whichever size you choose. If you want to know how much warmth that wattage actually puts into a room, our guide to whether electric fireplaces give off heat covers BTU and room size. Not sure which style fits your space? The fireplace finder narrows it down in a few questions.
FAQ
How many watts does an electric fireplace use?
Most plug-in electric fireplaces use 1,400 to 1,500 W on high heat and 700 to 750 W on low. With the heater off, the LED flame typically draws roughly 15 to 50 W depending on the model. The rating label and manual list the exact figures for your unit.
How many amps does an electric fireplace use?
Divide watts by 120 volts. A 1,500 W fireplace pulls 12.5 amps, a 1,400 W unit about 11.7 amps, and 750 W about 6.25 amps. On high heat, that’s a big share of a 15-amp circuit, so avoid sharing the circuit with other heavy loads.
Does an electric fireplace use a lot of electricity?
The heater does, by plug-in appliance standards: 1.5 kWh per hour on high, about 26¢ an hour at 17¢ per kWh. The flame effect alone uses very little, usually under a penny an hour.
How much does an electric fireplace cost to run per month?
At 17¢ per kWh and 4 hours a day, a 1,500 W unit on high costs about $30.60 a month, a 1,400 W unit about $28.56, and 750 W about $15.30. Thermostat cycling usually brings the real number lower.
Is an electric fireplace energy efficient?
At the point of use, nearly all the electricity becomes heat in the room, and there’s no chimney to lose warm air through. It’s most cost-effective as zone heat: warming the room you’re in while the rest of the house runs cooler. A heat pump still delivers heat more cheaply per unit than any resistance heater.





